Fostex VF08 Manuel d'utilisateur Page 62
- Page / 118
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
62
Recorder Functions
6
• To set editing points by marks:
Press the [TIME BASE SEL] key.
Each data field for the Start and End points changes to
show the current option by mark as shown below.
Use the [CURSOR up/down] keys to highlight the field for
the desired point, and press the [ENTER/YES] key.
The field starts blinking.
Use the [JOG] dial to select the desired mark and press
the [ENTER/YES] key.
The editing point is set to the selected mark.
<Note>
This operation can be performed only when any mark
is set. When no mark is set, "
00:ABS 0
" is the one and
only option for each point.
Press the [UNDO/REDO/F3] key while holding down the
[SHIFT] key.
The erase function is performed. When finished, "Com-
pleted!" appears on the screen.
<Hint>
You may use the [CURSOR >] to highlight "EXE" and press
the [ENTER/YES] key to perform the function, instead of
pressing the [UNDO/REDO/F3] key while holding down the
[SHIFT] key.
• By pressing the [UNDO/REDO] key after completing
the erase operation, you can return the track(s) to the
condition before performing the erase operation.
• By pressing the [UNDO/REDO] key just after
performing the undo operation, you can undo the
undo operation and return the track(s) to the
condition after performing the erase operation.
Note the following for performing the undo/redo op-
eration.
<Notes>
You can undo or redo only when the recorder is stopped.
If you carry out any of the following after performing
the erase operation, you cannot undo/redo the erase
operation.
1.Making a new recording
2.Performing a new editing
3.Letting the recorder run in playback (or recording)
mode and pass through the auto punch-in point while
the auto punch mode is active
4.Turning off the power of the VF08
5.Performing any of the program operations (select,
rename or delete).
Undo/redo of Erase
You can undo an erase operation, as well as redo it
(undo the undo operation).
- Owner’s Manual 1
- SAFETY INSTRUCTIONS 2
- Contents 3
- Recorder Functions 4
- Advanced Operation 4
- Save/Load of Song Data 4
- SETUP Mode 5
- Basic Features of VF08 6
- Precautions 7
- Before Operating 8
- EventAdditional track 9
- Time Base 10
- Names and Functions 11
- Names and functions 12
- Top panel (Mixer section) 13
- Rear panel 17
- Side panel 17
- Reformatting the hard disk 18
- Replacing a hard disk 19
- Formatting the Hard disk 21
- Basic Recording and Playback 22
- Switching the time base 23
- “Disk remain” indication 23
- Preliminary knowledge 24
- Preparation for recording 25
- Recording 26
- Playback 26
- Mark function 29
- ABS locate functions 30
- Punch in/out 30
- Auto punch in/out function 31
- Blinking 32
- Adjusting levels 33
- Setting pan position 33
- Adjusting EQ 33
- Setting effects 34
- Effect send level setting 34
- Effect type setting 34
- Analog mixdown 35
- Digital mixdown 35
- Mixer Functions 36
- Mix parameter section 37
- Editing EQ 38
- Editing Effects 41
- Flanger: 41
- Setting effect send levels 42
- Selecting an effect type 42
- About the effect types 44
- Effect parameter details 45
- Scene memory 47
- Storing the current scene 47
- Recalling a scene 47
- Deleting a scene 48
- Fader adjust 48
- Scene sequence 49
- Executing the scene sequence 50
- Digital scrubbing 52
- Performing digital scrubbing 52
- Vari Pitch 53
- Setting the speed 53
- Loop Function 54
- Creating a new program 56
- Selecting a program 57
- Deleting a program 57
- Editing a program title 57
- Track editing 58
- Undo/redo of Copy & Paste 60
- Erasing track data 61
- Undo/redo of Erase 62
- Track Exchange 63
- Editing Marks 64
- Enter a mark title 65
- Adding a mark 65
- Deleting a mark 66
- Locating a mark 66
- On/off of bounce mode 68
- Setting pan positions 68
- Setting level of each track 68
- Performing the track bounce 68
- Training mode 69
- Mastering mode 71
- Setting the mastering effects 72
- Effect library details 72
- Digital recording 74
- MIDI clock sync system 75
- Setup of the VF08 76
- Executing of recording 76
- Confirming MTC sync/MMC 77
- Execution of recording 77
- Setup of external equipment 77
- Confirming chase lock 78
- Save/Load of song data 80
- Additional 81
- Real Tracks 81
- Setting the external recorder 82
- Saving data 82
- Save/Load of Song data 83
- Loading data 84
- Formatting a backup disk 86
- Saving data to a SCSI disk 87
- Save/load a WAV file 92
- Saving a WAV file 93
- <About WAV files saved> 95
- Loading a WAV file 96
- To enter the SETUP mode 99
- Deleting a Time Signature 100
- Setting a tempo [“Tempo Set”] 101
- New Registering of Tempo 101
- SETUP mode 102
- Drive Setting [“Drive Sel”] 109
- Specifications 111
- MMC Command List 112
- Inquiry Message List 112
- Maintenance 113
- Block Diagram 114
- Declaration of EC Directive 116
- FOSTEX CORPORATION 118
- FOSTEX CORPORATION OF AMERICA 118
Produits connexes et manuels pour Pianos numériques Fostex VF08
(121 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.233 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels