Fostex VF08 Manuel d'utilisateur Page 57
- Page / 118
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
57
Recorder Functions
P01
P02
P03 P04
P05
P01
P02
P03 P04
P03 is deleted.
1
3
4
1
2
1
2
Selecting a program
When more than one program exists on the disk, you
have to select the desired program before starting
operations for recording, playback or editing.
Select the desired program by following the procedure
below while the recorder is stopped and the display
shows the Normal screen.
Press the [TRACK EDIT/
PGM] key while holding down
the [SHIFT] key.
The screen for selecting, renaming or deleting a program
appears. In the screen, all existing program numbers
and titles are shown.
Use the [JOG] dial to highlight the desired program and
then press the [SETUP/
F1] key while holding down the
[SHIFT] key.
Deleting a program
You can delete an unnecessary program individually.
To make recording or editing, a certain amount of disk
space is needed. By deleting unnecessary programs,
the available disk space increases.
<Notes>
• When only one program (P01) exists, if you try to
delete the program, the data in the program is deleted
but P01 remains.
• For example, when five programs (P01 through P05)
exist, if you delete P03, it looks like P05 is deleted. This
is because the program numbers higher than 03 move
down. In other words, P04 and P05 become P03 and
P04 respectively.
Note that you cannot undo or redo deleting the program.
Press the [TRACK EDIT/PGM] key while holding down
the [SHIFT] key.
The screen for selecting, renaming or deleting a program
appears. In the screen, all existing program numbers
and titles are shown.
Use the [JOG] dial to highlight the program to be de-
leted and then press the [UNDO/REDO/
F3] key while
holding down the [SHIFT] key.
The screen shows "Delete! Sure?", asking you confirm.
<Hint>
You may use the [CURSOR >] to highlight "DELETE" and
press the [ENTER/YES] key to bring up the screen
above, instead of pressing the [UNDO/REDO/F3] key
while holding down the [SHIFT] key.
Press the [ENTER/YES] key while holding down the
[RECORD] key.
The selected (highlighted) program is deleted, and the
following programs in the list move up.
Press the [EXIT/NO] key to switch to the Normal screen.
The previous program of the deleted program is se-
lected.
Editing a program title
You can edit a program title anytime by following the
procedure below.
Note that you can also enter a program title in the
process of creating a new program as mentioned ear-
lier.
Press the [TRACK EDIT/
PGM] key while holding down
the [SHIFT] key.
The screen for selecting, renaming or deleting a program
appears. In the screen, all existing program numbers
and titles are shown.
- Owner’s Manual 1
- SAFETY INSTRUCTIONS 2
- Contents 3
- Recorder Functions 4
- Advanced Operation 4
- Save/Load of Song Data 4
- SETUP Mode 5
- Basic Features of VF08 6
- Precautions 7
- Before Operating 8
- EventAdditional track 9
- Time Base 10
- Names and Functions 11
- Names and functions 12
- Top panel (Mixer section) 13
- Rear panel 17
- Side panel 17
- Reformatting the hard disk 18
- Replacing a hard disk 19
- Formatting the Hard disk 21
- Basic Recording and Playback 22
- Switching the time base 23
- “Disk remain” indication 23
- Preliminary knowledge 24
- Preparation for recording 25
- Recording 26
- Playback 26
- Mark function 29
- ABS locate functions 30
- Punch in/out 30
- Auto punch in/out function 31
- Blinking 32
- Adjusting levels 33
- Setting pan position 33
- Adjusting EQ 33
- Setting effects 34
- Effect send level setting 34
- Effect type setting 34
- Analog mixdown 35
- Digital mixdown 35
- Mixer Functions 36
- Mix parameter section 37
- Editing EQ 38
- Editing Effects 41
- Flanger: 41
- Setting effect send levels 42
- Selecting an effect type 42
- About the effect types 44
- Effect parameter details 45
- Scene memory 47
- Storing the current scene 47
- Recalling a scene 47
- Deleting a scene 48
- Fader adjust 48
- Scene sequence 49
- Executing the scene sequence 50
- Digital scrubbing 52
- Performing digital scrubbing 52
- Vari Pitch 53
- Setting the speed 53
- Loop Function 54
- Creating a new program 56
- Selecting a program 57
- Deleting a program 57
- Editing a program title 57
- Track editing 58
- Undo/redo of Copy & Paste 60
- Erasing track data 61
- Undo/redo of Erase 62
- Track Exchange 63
- Editing Marks 64
- Enter a mark title 65
- Adding a mark 65
- Deleting a mark 66
- Locating a mark 66
- On/off of bounce mode 68
- Setting pan positions 68
- Setting level of each track 68
- Performing the track bounce 68
- Training mode 69
- Mastering mode 71
- Setting the mastering effects 72
- Effect library details 72
- Digital recording 74
- MIDI clock sync system 75
- Setup of the VF08 76
- Executing of recording 76
- Confirming MTC sync/MMC 77
- Execution of recording 77
- Setup of external equipment 77
- Confirming chase lock 78
- Save/Load of song data 80
- Additional 81
- Real Tracks 81
- Setting the external recorder 82
- Saving data 82
- Save/Load of Song data 83
- Loading data 84
- Formatting a backup disk 86
- Saving data to a SCSI disk 87
- Save/load a WAV file 92
- Saving a WAV file 93
- <About WAV files saved> 95
- Loading a WAV file 96
- To enter the SETUP mode 99
- Deleting a Time Signature 100
- Setting a tempo [“Tempo Set”] 101
- New Registering of Tempo 101
- SETUP mode 102
- Drive Setting [“Drive Sel”] 109
- Specifications 111
- MMC Command List 112
- Inquiry Message List 112
- Maintenance 113
- Block Diagram 114
- Declaration of EC Directive 116
- FOSTEX CORPORATION 118
- FOSTEX CORPORATION OF AMERICA 118
Produits connexes et manuels pour Pianos numériques Fostex VF08
(121 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.805 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels