Fostex VF08 Manuel d'utilisateur Page 23
- Page / 118
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
23
Basic Recording/Playback
Normal screen
Normal screen with BAR/BEAT/CLK time base
Normal screen with MTC time base
Screen example while starting up
Remaining time displayed in time
Remaining time displayed in MB
1
2
3
4
65
Normal screen with ABS time base
LCD
This section describes major contents on the LCD
display and their operations.
Display when turning on the power
When turning on the power of the VF08 on which a
formatted hard disk is installed, the unit starts up and
“Initial..” and “version number” appears on the LCD
display, followed by “Current Dr”, “IDE”, “hard disk name
(momentarily)” and “record mode (Standard or
Quick)”. Then the unit gets ready at the beginning
(ABS 0) of the program which was selected when the
power was turned off last time. The current position
is shown by the time base previously selected.
The display that appears when the unit gets ready is
call “Normal screen”. The Normal screen shows the fol-
lowing items.
1. Scene number & name
With the initial setting, “S00: Initial Mix” appears.
2. Program number & name
With the initial setting, “P01: #0001” (#0001 is a tentative
name) appears.
3. Mark number & name
With the initial setting, “00: ABS 0” appears, showing that
the current location is at the beginning of the program. When
the recorder starts running, “:” between the number and
name is replaced with “+”.
4. Time base
With the initial setting, the ABS time base is selected.
You can change the time base by using the [TIME BASE SEL]
key (see the next section).
5. Level meters for Tracks 1 through 8
6. Master level meters for the Stereo output (L, R)
Switching the time base
Each press of the [TIME BASE SEL] key cycles the time
base of the Normal screen between “ABS”, “BAR/BEAT/
CLK” and “MTC”.
“Disk remain” indication
You can check the disk remaining space which shows
the “recordable space left on the current disk”.
The disk remaining space (REM) is shown during “Rec
ready” or “Recording”, in “time” when the remaining
time is less than 100 hours, or in “MB (Megabyte)” of
the remaining space when it exceeds 100 hours. Note
that the remaining time is shown as the recordable
time when you record onto a single track. , you can
calculate the recordable time for recording onto 8
tracks by dividing the displayed remaining time by
8.
- Owner’s Manual 1
- SAFETY INSTRUCTIONS 2
- Contents 3
- Recorder Functions 4
- Advanced Operation 4
- Save/Load of Song Data 4
- SETUP Mode 5
- Basic Features of VF08 6
- Precautions 7
- Before Operating 8
- EventAdditional track 9
- Time Base 10
- Names and Functions 11
- Names and functions 12
- Top panel (Mixer section) 13
- Rear panel 17
- Side panel 17
- Reformatting the hard disk 18
- Replacing a hard disk 19
- Formatting the Hard disk 21
- Basic Recording and Playback 22
- Switching the time base 23
- “Disk remain” indication 23
- Preliminary knowledge 24
- Preparation for recording 25
- Recording 26
- Playback 26
- Mark function 29
- ABS locate functions 30
- Punch in/out 30
- Auto punch in/out function 31
- Blinking 32
- Adjusting levels 33
- Setting pan position 33
- Adjusting EQ 33
- Setting effects 34
- Effect send level setting 34
- Effect type setting 34
- Analog mixdown 35
- Digital mixdown 35
- Mixer Functions 36
- Mix parameter section 37
- Editing EQ 38
- Editing Effects 41
- Flanger: 41
- Setting effect send levels 42
- Selecting an effect type 42
- About the effect types 44
- Effect parameter details 45
- Scene memory 47
- Storing the current scene 47
- Recalling a scene 47
- Deleting a scene 48
- Fader adjust 48
- Scene sequence 49
- Executing the scene sequence 50
- Digital scrubbing 52
- Performing digital scrubbing 52
- Vari Pitch 53
- Setting the speed 53
- Loop Function 54
- Creating a new program 56
- Selecting a program 57
- Deleting a program 57
- Editing a program title 57
- Track editing 58
- Undo/redo of Copy & Paste 60
- Erasing track data 61
- Undo/redo of Erase 62
- Track Exchange 63
- Editing Marks 64
- Enter a mark title 65
- Adding a mark 65
- Deleting a mark 66
- Locating a mark 66
- On/off of bounce mode 68
- Setting pan positions 68
- Setting level of each track 68
- Performing the track bounce 68
- Training mode 69
- Mastering mode 71
- Setting the mastering effects 72
- Effect library details 72
- Digital recording 74
- MIDI clock sync system 75
- Setup of the VF08 76
- Executing of recording 76
- Confirming MTC sync/MMC 77
- Execution of recording 77
- Setup of external equipment 77
- Confirming chase lock 78
- Save/Load of song data 80
- Additional 81
- Real Tracks 81
- Setting the external recorder 82
- Saving data 82
- Save/Load of Song data 83
- Loading data 84
- Formatting a backup disk 86
- Saving data to a SCSI disk 87
- Save/load a WAV file 92
- Saving a WAV file 93
- <About WAV files saved> 95
- Loading a WAV file 96
- To enter the SETUP mode 99
- Deleting a Time Signature 100
- Setting a tempo [“Tempo Set”] 101
- New Registering of Tempo 101
- SETUP mode 102
- Drive Setting [“Drive Sel”] 109
- Specifications 111
- MMC Command List 112
- Inquiry Message List 112
- Maintenance 113
- Block Diagram 114
- Declaration of EC Directive 116
- FOSTEX CORPORATION 118
- FOSTEX CORPORATION OF AMERICA 118
Produits connexes et manuels pour Pianos numériques Fostex VF08
(121 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.170 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels