Fostex VF08 Manuel d'utilisateur Page 29
- Page / 118
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
29
Basic Recording/Playback
1
2
[ I] key
[I
] key
1
2
3
Mark function
The VF08 has the Mark function which allows you to set marks at the desired positions in a song.
You can locate a mark position immediately, as well as use mark positions for the punch in and out points, beginning
and end points for repeat and editing points for track editing such as copy, move, erase, etc.
This section describes how to set, delete and locate a mark. For details about editing a mark, see “Recorder func-
tions” described later.
Setting a mark on the fly
In the initial condition, Mark 00 is automatically en-
tered at the beginning of the current program (ABS
0) and named “ABS 0”.
You can enter up to 99 marks (Mark 01 through 99).
Mark number and name are shown on the Normal
screen as the arrow points in the screen example be-
low. (You cannot edit or delete Mark 00.)
During playback (or while stopped), press [|<< /
MARK]
key while holding down the [SHIFT] key.
“Entry Mark” is shown briefly and a mark is entered at
the current position.
Also the time marked is entered in the mark map list
(see “Recorder functions” for details).
To enter another mark, repeat step 1) above.
<Note>
Marks are assigned in ascending order of ABS time.
For example, even if you enter marks in order as shown
in the upper diagram below, the mark numbers are as-
signed as shown in the lower diagram.
Locating a mark
• Pressing [|<<] key locates the previous mark.
In the example above, each time you press the key from
the current position, the recorder will locate Mark 03 ->
02 -> 01 -> 00.
• Pressing [>>|] key locates the next mark.
In the example above, each time you press the key from
the current position, the recorder will locate Mark 04 ->
05 -> 06.
The current (located) mark number is shown on the
Normal screen.
Deleting a mark
You can delete unnecessary mark
While stopped, locate the mark to be deleted using the
[|<<] or [>>|] key.
The mark to be deleted is shown on the screen.
Press the [>>|/DELETE] key while holding down the
[SHIFT] key.
A pop-up panel asking for confirmation to delete the
current mark appears, in which “Sure?” blinks.
To cancel the operation for deletion, press the [EXIT/
NO] key.
Press the [ENTER/YES] key while holding down the
[RECORD] key.
The current mark is deleted.
You can locate a mark using the [|<<] or [>>|] key.
Current position
- Owner’s Manual 1
- SAFETY INSTRUCTIONS 2
- Contents 3
- Recorder Functions 4
- Advanced Operation 4
- Save/Load of Song Data 4
- SETUP Mode 5
- Basic Features of VF08 6
- Precautions 7
- Before Operating 8
- EventAdditional track 9
- Time Base 10
- Names and Functions 11
- Names and functions 12
- Top panel (Mixer section) 13
- Rear panel 17
- Side panel 17
- Reformatting the hard disk 18
- Replacing a hard disk 19
- Formatting the Hard disk 21
- Basic Recording and Playback 22
- Switching the time base 23
- “Disk remain” indication 23
- Preliminary knowledge 24
- Preparation for recording 25
- Recording 26
- Playback 26
- Mark function 29
- ABS locate functions 30
- Punch in/out 30
- Auto punch in/out function 31
- Blinking 32
- Adjusting levels 33
- Setting pan position 33
- Adjusting EQ 33
- Setting effects 34
- Effect send level setting 34
- Effect type setting 34
- Analog mixdown 35
- Digital mixdown 35
- Mixer Functions 36
- Mix parameter section 37
- Editing EQ 38
- Editing Effects 41
- Flanger: 41
- Setting effect send levels 42
- Selecting an effect type 42
- About the effect types 44
- Effect parameter details 45
- Scene memory 47
- Storing the current scene 47
- Recalling a scene 47
- Deleting a scene 48
- Fader adjust 48
- Scene sequence 49
- Executing the scene sequence 50
- Digital scrubbing 52
- Performing digital scrubbing 52
- Vari Pitch 53
- Setting the speed 53
- Loop Function 54
- Creating a new program 56
- Selecting a program 57
- Deleting a program 57
- Editing a program title 57
- Track editing 58
- Undo/redo of Copy & Paste 60
- Erasing track data 61
- Undo/redo of Erase 62
- Track Exchange 63
- Editing Marks 64
- Enter a mark title 65
- Adding a mark 65
- Deleting a mark 66
- Locating a mark 66
- On/off of bounce mode 68
- Setting pan positions 68
- Setting level of each track 68
- Performing the track bounce 68
- Training mode 69
- Mastering mode 71
- Setting the mastering effects 72
- Effect library details 72
- Digital recording 74
- MIDI clock sync system 75
- Setup of the VF08 76
- Executing of recording 76
- Confirming MTC sync/MMC 77
- Execution of recording 77
- Setup of external equipment 77
- Confirming chase lock 78
- Save/Load of song data 80
- Additional 81
- Real Tracks 81
- Setting the external recorder 82
- Saving data 82
- Save/Load of Song data 83
- Loading data 84
- Formatting a backup disk 86
- Saving data to a SCSI disk 87
- Save/load a WAV file 92
- Saving a WAV file 93
- <About WAV files saved> 95
- Loading a WAV file 96
- To enter the SETUP mode 99
- Deleting a Time Signature 100
- Setting a tempo [“Tempo Set”] 101
- New Registering of Tempo 101
- SETUP mode 102
- Drive Setting [“Drive Sel”] 109
- Specifications 111
- MMC Command List 112
- Inquiry Message List 112
- Maintenance 113
- Block Diagram 114
- Declaration of EC Directive 116
- FOSTEX CORPORATION 118
- FOSTEX CORPORATION OF AMERICA 118
Produits connexes et manuels pour Pianos numériques Fostex VF08
(121 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.450 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels