Fostex MR-8MKII Manuel d'utilisateur Page 86
- Page / 154
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
86
MR-8mkII Owner’s Manual (MIDI synchronization)
The following describes how to synchronize a sequencer to the MR-8mkII which supports MTC
(MIDI Time code).
Connect the [MIDI OUT] connector of the MR-8mkII to the [MIDI IN] connector of an external
MIDI sequencer using a MIDI cable. (Note that no MIDI cable is supplied with the MR-8mkII.
Use a commercially available MIDI cable.)
1) Set the "Midi Sync Out" item in the "System"
menu of the menu mode to "MTC" and the "MTC
Frame Rate" to an appropriate frame rate.
See "MIDI sync/MTC frame rate settings"
described below for details.
2) Enable the external MIDI sequencer to
synchronize to MTC.
See the operation manual of the sequencer for
details.
3) Press the [PLAY] key of the MR-8mkII to start
playback.
The sequencer automatically starts playback
while synchronizing to the MR-8mkII
While the MR-8mkII is stopped, you can set
the reference of MIDI synchronization to
"MTC" and the MTC frame rate appropriately
to match the sequencer.
2) Rotate the JOG dial to select "System", and press
the [MENU/ENTER] key.
The display now shows the first page of the
system menu screen, where "<< BACK" is
highlighted initially.
<MTC start time>
The MTC from the MR-8mkII has one hour off-
set to the ABS time (the offset value is fixed).
Therefore, when you start the MR-8mkII from
the beginning of a song (ABS ZERO), the MTC
starts from "01h 00m 00s 00f".
1) While the recorder is stopped, press the
[MENU/ENTER] key to enter the menu mode.
The display now shows the first page of the
menu selection screen, where "<< Back" is
highlighted initially (selecting "<< Back"
returns to the previous screen).
MIDI OUTUSB HOSTCOMPACTFLASH CARD
MIDI IN
MIDI sequencer, etc.
Connection
Settings of the MR-8mkII and MIDI sequencer
MIDI sync/MTC frame rate settings
3) Rotate the JOG dial to select "Midi Sync Out",
and press the [MENU/ENTER] key.
Synchronization using MTC
- Owner’s Manual 1
- SAFETY INSTRUCTIONS 2
- Important Safety Instructions 3
- Table of contents 4
- Read this chapter first! 9
- Introduction 10
- MR-8mkII main features 10
- Precautions before using 11
- The basics of the MR-8mkII 12
- About song 13
- Time base 14
- [TRIM] control 15
- Preparation 17
- Preparation of power supply 18
- About song modes 19
- Fostex website: 19
- <Important!>: 20
- Turning on the power 21
- Turn off the power 22
- Low battery indication 22
- Backlight facility 22
- Creating a new song 23
- How to enter a name 24
- Names and functions 25
- Top panel 1 26
- Top panel 2 27
- Rear panel 29
- Side panel 30
- Bottom panel 30
- LCD display 31
- Selecting a time base mode 32
- MENU mode screen 33
- Warning message 33
- Basic recording operations 35
- Input connection 36
- Selectable recording tracks 37
- Recording onto a single track 38
- <Notes>: 39
- Overdubbing basics 42
- Basic mixdown 44
- 3 x cueing 46
- Play mode 47
- Auto play mode 48
- Auto return mode 48
- Loop mode 48
- Locate function 50
- • To set the LOCATE B point: 51
- • To set the LOCATE A point: 51
- Locating 52
- Punch in/out 53
- Auto punch in/out 56
- [UNDO/REDO] key 58
- Using effects 59
- Mic simulation effects 60
- Amp simulation effects 60
- Selecting an effect type 61
- Selecting a delay type 61
- [REVERB / DELAY TIME] control 62
- Track bouncing 65
- Preliminary knowledge 66
- Signal flow of track bouncing 67
- Rehearsal of track bouncing 68
- Actual track bouncing 69
- Typical bouncing (Fig. 1) 74
- Rhythm guide function 75
- Creating the conductor map 78
- Editing the bar offset 81
- Setting the tempo map 82
- • Editing a tempo event 84
- MIDI synchronization 85
- Synchronization using MTC 86
- Connection 87
- Song management 89
- Selecting the desired song 90
- Editing a song name 91
- Deleting an unnecessary song 92
- Protecting a song 93
- <Note> 94
- Track data editing 95
- Erasing track data 96
- Copying/pasting track data 97
- Moving track data 99
- <Note>: 100
- Exchanging whole track data 101
- Part data editing 103
- Erasing the part(s) 105
- Copying/pasting the part(s)-1 106
- Copying/pasting the part(s)-2 108
- Pasting clipboard data 110
- Moving the part(s) 111
- Exchange the part(s) 113
- WAV file conversion 116
- <Editing a file name> 117
- Notes on exporting a file 118
- <Important note> 119
- Protecting the card 120
- Archiving a song 121
- Burning an audio CD 123
- Read this page before using! 124
- #####001.wav 125
- #####002.wav 125
- #####003.wav 125
- #####008.wav 125
- *********.wav 125
- Viewing TOC 129
- Other functions 131
- CompactFlash 132
- Card formatting 132
- Peak hold time setting 133
- Auto Delete function on/off 135
- Beat resolution mode on/off 136
- Phantom power on/off 137
- Initializing the MR-8mkII 138
- Troubleshooting 139
- Troubles for recording 140
- Troubles for playback 141
- Troubles for effect 141
- Other troubles 142
- Troubles for USB connection 142
- Troubles for power supply 142
- MR-8mkII Specifications 143
- Specifications 144
- Physical dimensions 145
- Block diagram 146
- NEW SONG 147
- MIDI Implementation Chart 148
- Declaration of EC Directive 150
- FOR THE US CUSTOMERS ONLY 151
- SHIPPING 152
- FOSTEX CO 154
- FOSTEX AMERICA 154
Produits connexes et manuels pour Audio Fostex MR-8MKII
(122 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.955 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels