Fostex MR-8MKII Manuel d'utilisateur Page 117
- Page / 154
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
117
MR-8mkII Owner’s Manual (Data export to a personal computer)
5) Press the [MENU/ENTER] key.
The MR-8mkII quits the conversion function
and the display returns to the home screen.
<Editing a file name>
You can edit a file name by the following
procedure.
2) Enter a new name using the character
entry keys.
Pressing a different character entry key
automatically moves the cursor right.
If two successive characters are assigned
to the same character entry key, rotate
the JOG dial after selecting the first
character to move the cursor right.
<Note>:
If you convert data with the same name
as previously converted data, the following
screen appears on the display.
This screen warns you that the WAV file with
the same name already exists and asks you to
carry out the conversion by overwriting the ex-
isting file or cancel the conversion.
If you carry out the conversion by overwriting
the existing file, rotate the JOG dial to move the
cursor to "[YES]", and press the [MENU/ENTER]
key.
If you do not want to overwrite the existing file,
rotate the JOG dial to move the cursor to "[NO]",
then press the [MENU/ENTER] key. The display
returns to show the screen for editing the file
name, so you can enter a different file name and
then carry out the conversion.
If you want to cancel the conversion when the
screen above is shown, rotate the JOG dial to
move the cursor to "[NO]" and press the [MENU/
ENTER] key to show the screen for editing the
file name, and then press the [STOP] key to quit
the conversion function.
3) After entering a new name, press the
[MENU/ENTER] key.
Then, by pressing the [MENU/ENTER] key while
holding down the [RECORD] key to carry out the
WAV file conversion.
While the rightmost character is flash-
ing, pressing the [UNDO/REDO]/[DE-
LETE] key repeatedly deletes the cur-
rent file name.
When the conversion is completed, the display
shows "Completed".
Flashing
<Note>:
If you cancel the conversion in the
middle, no file (incomplete file) is created.
4) Press the [MENU/ENTER] key while holding
down the [RECORD] key.
The file conversion starts and the percent
number on the screen counts up as the
conversion progresses.
To cancel the conversion in the middle, press
the [STOP] key.
1) After selecting the range of track data to be
converted, rotate the JOG dial to move the
cursor to "Name" and press the
[MENU/ENTER] key.
The rightmost character of the file name
starts flashing.
You can now start editing.
- Owner’s Manual 1
- SAFETY INSTRUCTIONS 2
- Important Safety Instructions 3
- Table of contents 4
- Read this chapter first! 9
- Introduction 10
- MR-8mkII main features 10
- Precautions before using 11
- The basics of the MR-8mkII 12
- About song 13
- Time base 14
- [TRIM] control 15
- Preparation 17
- Preparation of power supply 18
- About song modes 19
- Fostex website: 19
- <Important!>: 20
- Turning on the power 21
- Turn off the power 22
- Low battery indication 22
- Backlight facility 22
- Creating a new song 23
- How to enter a name 24
- Names and functions 25
- Top panel 1 26
- Top panel 2 27
- Rear panel 29
- Side panel 30
- Bottom panel 30
- LCD display 31
- Selecting a time base mode 32
- MENU mode screen 33
- Warning message 33
- Basic recording operations 35
- Input connection 36
- Selectable recording tracks 37
- Recording onto a single track 38
- <Notes>: 39
- Overdubbing basics 42
- Basic mixdown 44
- 3 x cueing 46
- Play mode 47
- Auto play mode 48
- Auto return mode 48
- Loop mode 48
- Locate function 50
- • To set the LOCATE B point: 51
- • To set the LOCATE A point: 51
- Locating 52
- Punch in/out 53
- Auto punch in/out 56
- [UNDO/REDO] key 58
- Using effects 59
- Mic simulation effects 60
- Amp simulation effects 60
- Selecting an effect type 61
- Selecting a delay type 61
- [REVERB / DELAY TIME] control 62
- Track bouncing 65
- Preliminary knowledge 66
- Signal flow of track bouncing 67
- Rehearsal of track bouncing 68
- Actual track bouncing 69
- Typical bouncing (Fig. 1) 74
- Rhythm guide function 75
- Creating the conductor map 78
- Editing the bar offset 81
- Setting the tempo map 82
- • Editing a tempo event 84
- MIDI synchronization 85
- Synchronization using MTC 86
- Connection 87
- Song management 89
- Selecting the desired song 90
- Editing a song name 91
- Deleting an unnecessary song 92
- Protecting a song 93
- <Note> 94
- Track data editing 95
- Erasing track data 96
- Copying/pasting track data 97
- Moving track data 99
- <Note>: 100
- Exchanging whole track data 101
- Part data editing 103
- Erasing the part(s) 105
- Copying/pasting the part(s)-1 106
- Copying/pasting the part(s)-2 108
- Pasting clipboard data 110
- Moving the part(s) 111
- Exchange the part(s) 113
- WAV file conversion 116
- <Editing a file name> 117
- Notes on exporting a file 118
- <Important note> 119
- Protecting the card 120
- Archiving a song 121
- Burning an audio CD 123
- Read this page before using! 124
- #####001.wav 125
- #####002.wav 125
- #####003.wav 125
- #####008.wav 125
- *********.wav 125
- Viewing TOC 129
- Other functions 131
- CompactFlash 132
- Card formatting 132
- Peak hold time setting 133
- Auto Delete function on/off 135
- Beat resolution mode on/off 136
- Phantom power on/off 137
- Initializing the MR-8mkII 138
- Troubleshooting 139
- Troubles for recording 140
- Troubles for playback 141
- Troubles for effect 141
- Other troubles 142
- Troubles for USB connection 142
- Troubles for power supply 142
- MR-8mkII Specifications 143
- Specifications 144
- Physical dimensions 145
- Block diagram 146
- NEW SONG 147
- MIDI Implementation Chart 148
- Declaration of EC Directive 150
- FOR THE US CUSTOMERS ONLY 151
- SHIPPING 152
- FOSTEX CO 154
- FOSTEX AMERICA 154
Produits connexes et manuels pour Audio Fostex MR-8MKII
(122 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.129 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels