Fostex VF160EX Manuel d'utilisateur télécharger pdf (Page 32)

PLAY

1. Press the [REWIND] key while the [STOP] key is depressed

to locate ABS 0.

2. Press the [PLAY] key to start playback.

The play level of track 1 can be adjusted with the ch1 fader.

This concludes the procedures to check the sound recorded.

Tips: UNDO/REDO

Press the [UNDO/REDO] key after recording to return to

the prerecording state (UNDO). Press the [UNDO/REDO]

key again to return to the original state of the recording

on track 1 (REDO). The UNDO/REDO function is effective

for all recordings.

Cancel READY Status of Recording Track

Press once again the [DIRECT-REC TRACK] key that is lit

up RED, then press the [CH STATUS/CH SEL] key of the

channel that is in the READY mode to cancel the ready

state of the track recorded and to put that track in the

SAFE mode. Then press the [EXIT/NO] key to return to

the Normal Display.

Preparing to Record

WARNING!

In DIRECT Recording, all channel faders are basically

“TRK”. If there is channel in which the “IN (Input)”

(RED: Flashing), press the

[CH STATUS/CH SEL]

key of

that channel so it is a “TRK”.

Press the [DIRECT-REC TRK] key (RED: Flashing).

The menu to select the track to record appears.

Press the [CH STATUS/CH SEL] key of ch1 (Key: Flashing

RED).

Indicates

that ch1 is

READY.

Press the [EXIT/NO] key to return to the Normal Display.

[CH STATUS/CH SEL] key of ch1 -> Alternately Flashes

GREEN/RED

* Indicates that trk1 is “RDY (Ready)”.

Press [RECORD] key to set trk1 to the Input Monitor mode

(Key: Flashing RED).

Set the ch1 fader and master fader to “0”.

Output sound from the sound source while adjusting the

[TRIM]1/9/A gain to an optimal level.

The guideline for optimal gain is the border of the [PEAK]

LED lighting ON or OFF, when the sound source is at the

maximum volume. Adjustments should also ensure that

the signal does not exceed 0 on the LCD level meter.

To listen to the sound turn up the [MON OUT] knob or

[PHONES] knob.

WARNING!

Be careful not to excessively raise the volume of the

[MON OUT]

[PHONES]

level. Prolonged exposure to

loud sounds may have an adverse effect on hearing.

RECORD

1. Press the [REWIND] key while the [STOP] key is

depressed, to locate ABS 0 (Locate ABS 0).

2. Press the [PLAY] key while the [RECORD] key is

depressed to start recording.

The RED light of [CH STATUS/CH SEL] key and [RECORD] key

of ch1 lights up to indicate that ch1 is recording.

3. Press the [STOP] key to stop the recording operations.

The LCD will show a “Please Wait” message and then return

to the Normal Display.

This completes the process to record on track 1.

Check the sound recorded using the following procedures.

Tips: Level meter

When carrying out step 8 mentioned above, levels for

channel 1 and masters L and R are shown in the meters

on the Normal display.

The channel 1 fader controls the signal level sent to the

stereo busses L and R, which you monitor.

If you completely drop down the channel 1 fader, you

cannot monitor the sound, but the input level of chan-

nel 1 (= recording level of track 1) is not affected.

To control the input level of each channel, use the [TRIM]

knob as mentioned in step 8.

Connect the sound source to record to the [INPUT] 1/9/

A jack.

Press the [INPUT SEL] key (Key: Flashes ORANGE).

[CH STATUS/CH SEL] key of ch9-16 -> Flashes GREEN

Indicates that all channels are “TRK (Track)” (the

following LCD display appears).

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 157 158

Commentaires sur ces manuels

Pas de commentaire

Fostex VF160EX Manuel d'utilisateur Page 32

Commentaires sur ces manuels